Skip to main content

Pioneer SPH-PF97BT 9" Head Unit Installation

Posted by ATD ADMIN on 10th Nov 2026

Hi,

Thank you very much for your purchase.

Here you can find documentation for installing our range of bespoke Pioneer SPH-PF97BT perfect fit radios.

Customer Instructions 

Using the Pioneer SPHPF97BT With an ATD CANBUS Decoder or Analogue Loom 

These instructions apply whether you are using an ATD CANBUS decoder box or an analogue (resistive key) steering control loom. 

 

1. Understanding the Connectors 

Your installation harness will include: 

  1. A 16pin plug
  • This inserts directly into the back of the Pioneer SPHPF97BT. If you are using an analogue resistivekey loom, the steeringkey wires will already be prepinned into this 16pin block. 
  1. An 8pin block (if CANBUS)
  • This also plugs directly into the Pioneer. This block carries additional data and accessory signals when a CAN decoder is used. 
  1. CANBUS Decoder Box (if supplied)
  • The decoder sits between the vehicle and the Pioneer. The loom plugs only fit one way — do not force them. 

 

2. Parking Brake Wire — Critical Step 

The Pioneer SPHPF97BT will lock out many menus (greyedout options) unless the parking brake wire is connected correctly. 

  • Connect the light green parking brake wire to the vehicle’s parking brake signal. 
  • Without this connection, you will not be able to access key setup menus. 

 

3. Check the CANBUS Pathway Label 

If you are using a decoder box: 

  • Look at the sticker on the decoder box. It will show a CANBUS pathway code (e.g., “HiWorld-VW-VW MQB-ALL”). Make a note of this — you will need it during first setup. 

 

4. First PowerOn Setup 

When you first turn on the Pioneer: 

  1. The unit will ask you to select the CANBUS pathway. 
  1. Choose the exact route printed on the decoder box label. 
  1. Confirm the selection. 
  1. Allow the unit to initialise. 

After this, go to: 

Settings → System → Demo Mode → OFF | This prevents the unit from returning to demo behaviour. 

 

5. Setting Up Steering Wheel Controls 

From the home screen: 

  1. Open the CAR FEATURES app. 
  1. Select the grey SETTINGS box. 
  1. Choose Steering Wheel Controls. 

Now select the correct mode: 

If you are using a CANBUS decoder box: 

  • Choose WITH ADAPTOR. 
  • You can now manually assign each steering wheel button and save the configuration. 

If you are using an analogue resistivekey loom (no decoder box): 

  • Choose WITHOUT ADAPTOR. 
  • Select the vehicle region (e.g., Europe). 
  • Manually assign each steering wheel button and save. 

 

6. Final Checks 

  • Confirm the unit powers on with ignition. 
  • Test steering wheel controls. 
  • Check reverse trigger (if applicable). 
  • Ensure dimmer/illumination works if supported by the vehicle. 
  • Verify that all menus are accessible (parking brake wire must be connected). 

We sincerely hope you enjoy your new Pioneer Radio.

2026-01-01,2026-04-03,2026-04-06,2026-05-04,2026-05-25,2026-08-31,2026-12-25,2026-12-28,2027-01-01,2027-03-26,2027-03-29,2027-05-03,2027-05-31,2027-08-30,2027-12-27,2027-12-28,2028-01-03,2028-04-14,2028-04-17,2028-05-01,2028-05-29,2028-08-28,2028-12-25,2028-12-26